Easy Machine Applique Tutorial: How to Applique in No Time

Have you tried applique?  If not, are you scared of something new?  No matter!  There are several types of applique, some harder than others.  Today I will show you a very easy and basic method of machine applique.  I hope this helps get you started.

Materials.

• template - the shape you want to applique.  It can be a printout from a pattern or a drawing or something you trace from a coloring book.  The possibilities are endless!
• fusible web - there are many common brands of fusible web.  Heat 'N' Bond Lite is typically what I use.  Steam-A-Seam, MistyFuse, and Pellon Wonder-Under are other brands I have tried.  Make sure to get sew-able fusible web.  There is a non-sewable version of fusible web and if you try to sew through it, it will gum up your needle with glue.  Trust me.
• fabric - a piece slightly larger than your desired applique shape.  You will also need a background fabric to fuse your applique shape to.  This may be another rectangle for a quilt block, a t-shirt, a bag, a quilt top, etc.
• interfacing or stablizer (optional) - if your background fabric is lightweight or thin, you may want to place interfacing underneath the background fabric to stiffen it.

1.  Place the fusible web rectangle, bumpy side down, on top of pattern sheet and trace the applique shape.    

2. Cut out the shape leaving a 1/4” margin around the shape. Place the fusible web with the traced shape bumpy side down on the wrong side of the fabric.  Press to fuse the fusible web to the applique fabric.  Make sure to read the manufacturer’s instructions prior to beginning for appropriate heat settings and length of time to press.  For Heat 'N' Bond Lite, I usually press for about 8-10 seconds on a low (medium-low) setting.

3.  Cut out the shape carefully. 

4.   Peel the paper backing off of the shape.  Now your fabric shape will have the fusible web on the wrong side of the fabric.  It is ready to apply to your background.

5.  Fuse the shape (wrong side down) to the right side of the background fabric, making sure to center the shape.  Use the same technique and settings as step 2. 

*Note*  If you want to use an interfacing to support the background, now is the time to apply it.  Either fuse the interfacing to the background or pin it in place on the wrong side of the background fabric.  Honestly, I usually skip this step.  Call me lazy - but I have found I don't need it when appliquing for a quilt.  The Heat 'N' Bond Lite product gives the applique shape some stiffness.  If I am working on a t-shirt though, the interfacing is very helpful.

6.  Zigzag or blanket stitch around the shape to secure the appliqué.  Patience!!  Sewing a tight zigzag around a complex shape can take some time, but it is well worth the flair it adds to the piece.  Try experimenting with the tightness of your zig zag.  Most machines allows you to adjust how close the stitches are.  If you are appliquing on clothing, I would choose a tighter zig zag stitch because clothing will be washed repeatedly.  You may not need such a tight stitch for other applications, such as a quilt.


Isn't she cute?

Finished Applique Shape

And here it is in my quilt top!

I hope this helps get you started with applique.  It can be so fun to personalize handmade gifts.

Sisters' Ten Modern BOM April Block: Lady of the Lake

April already?  Today the next block for the Sisters' Ten Modern Block of the Month Club is up!  This block is a classic.  Get ready to get your HST on - it's Lady of the Lake.

Cutting Instructions.

For 12" blocks.

• Cut (10) 3 1/8" x 3 1/8" squares of Fabric A (background).
• Cut (10) 3 1/8" x 3 1/8" squares of Fabric C.
• Cut (1) 9 1/4" x 9 1/4" square of Fabric A (background).
• Cut (1) 9 1/4" x 9 1/4" square of Fabric B.

For 9" blocks.

• Cut (10) 2 5/8" x 2 5/8" squares of Fabric A (background).
• Cut (10) 2 5/8" x 2 5/8" squares of Fabric C.
• Cut (1) 7 1/4" x 7 1/4" square of Fabric A (background).
• Cut (1) 7 1/4" x 7 1/4" square of Fabric B.

Piecing Instructions.

*Use a scant 1/4" on all seam allowances. See the Scant Rant series for details.

1. Make a Half-Square Triangle (HST) unit with Fabric A and Fabric B. Use (1) Fabric A square and the (1) Fabric B square to make (2) total Half-Square Triangle units using the method in this tutorial. The HSTs should be trimmed down to:

                     
12" blocks:  8 1/2" (unfinished size).

9" blocks:  6 1/2" (unfinished size).

**NOTE** The 2 large HSTs made in this step will be used for both blocks you make this month.  Each block requires only 1 of these HSTs.  I wanted to keep the same method of construction and reduce waste.

2. Make Half-Square Triangle (HST) units with Fabric A and Fabric C. Use the remaining (10) Fabric A squares and the (10) Fabric C squares to make (20) total Half-Square Triangle units using the method in this tutorial. The HSTs should be trimmed down to:

12" blocks:  2 1/2" (unfinished size).

9" blocks: 2" (unfinished size).

3. Layout the Half-Square Triangle Units as shown below.

4. Sew each of the four rows that surround the center A/B HST together, pressing seams in one direction.

5. Sew the rows on the left and right side to the large center half-square triangle.

6.  Sew the remaining rows to the top and bottom of the unit from step 5.

7. Make (2) blocks. They may be identical blocks or made from differing fabrics for a scrappier look.  As I pointed out in the note above in Step 1, to reduce waste, I used the same fabric for both the large center HSTs in these blocks.  Don't worry if you think they look too similar!  Once the blocks are separated on opposite sides of the quilt, it will be much harder to notice.

Fabric is Alison Glass for Andover, Lucky Penny with background Quilter's Linen in Straw by Robert Kaufman.

10-Minute Sewing Project: How to Sew a Lanyard

Who doesn't love a quick and easy project?  I sure do!  And since I needed to replace the lanyard I had, I thought I'd do a quick tutorial for you all.  You'll probably spend more time choosing what fabric to use than actually making this lanyard.

Materials.

• 3 3/4" x width of fabric (wof) strip*
• 1" swivel hook
• coordinating thread

*The width of the fabric strip will depend upon the size of the swivel hook.  I am using a 1" hook, pictured on the right and middle below.  If you are using a smaller hook (pictured left), cut your fabric strip 1/4" less than 4 x the width of your hook.  (i.e. for the 1" inch hook, 4 * 1" - 1/4" is 3 3/4".  for a 1/2" hook, 4 * 1/2" - 1/4" is 1 3/4".)

1.  Fold the fabric strip in half lengthwise and press to create a crease in the center of the strip.

2.  Open the strip.  This time fold the outside edge to meet the pressed center line.  Press.

3.  Repeat this process of folding and pressing with the other side of the fabric strip.

4.  Fold the unit from step 3 in half again, tucking the unfinished edges inside the strip.  Press and pin in place.

5.  Topstitch 1/8" away from the edge on both sides of the strip.

This will give the strip a nice finished look.

6.  Fold the strip in half, bringing the two raw edges together.  Slip the swivel hook over the two raw ends.  Next, fold the ends over first 1/2" to tuck raw edges inside, then fold again 1 1/2".

7.  Stitch a square with an X through it to secure.  **Hint** if you have a walking foot for your sewing machine, it really helps sew over all the layers.  I definitely recommend it for this step.

And here I am modeling my new lanyard...  I use one all the time for my keys.  It seems I am always carrying 8 things in the parking lot - a baby, grocery bags, holding a little hand, packages, our to-go order from Panera, etc. - and knowing exactly where my keys are and having them easily accessible makes life a little easier for me... :)

Hope you enjoy this quick project!